SolidForce PCIe/NVMe M.2 SSD 10Gbps 인클로저 라이트
M.2 NVMe SSD 인클로저 어댑터, 도구가 전혀 필요하지 않습니다. USB C 3.1 Gen 2 10Gbps - NVMe PCIe M-키(B+M 키) 솔리드 스테이트 드라이브 외부 인클로저. M.2 NVMe SSD 크기 2242/2260/2280용 UASP 트림을 지원합니다.
Adopts USB 3.1 Gen 2 that M.2 Enclosure up to 10 Gbps, capable of performance over 900MB/s read/write when using high-performance SSD. The perfect solution for data transfer and data backup, the actual transfer speed depends on the speed of USB Port type, your computer performance, etc. Backward compatible with USB 3.1 Gen1 up to 5Gbps.
Compatible with M.2 NVMe PCIe M Key & B+M Key SSD up to 2TB, applicable to sizes 2242/2260/2280 SSDs. Not compatible with M.2 SATA SSDs, M.2 PCIe AHCI SSDs, M.2 PCIe devices such as WiFi and capture cards, mSATA SSDs, and non-M.2 form factor SSDs. Note: M.2 NVMe SSD is not included;
Supports Windows, Mac OS, Linux, Android.
How to Use:
1. Press the lock button on the product.
2. Pull out the PCBA board.
3. Insert the M.2 SSD diagonally down to the PCIe / NVMe slot.
4. Remove the silicone pad and heat sink from the package.
5. Paste the silicone pad accessories on the M.2 SSD card below.
6. Paste the heat sink accessories on the silicone pad below.
7. Gently press down on the M.2 SSD with your fingers and snap it into the plastic snap-on case. 8. When disassembling, also push the buckle outward to release it.
- When installing M.2 SSDs, please be careful of static electricity (it is recommended to place your hands on metal objects to discharge).
- With the M Key interface which belongs to the NVMe protocol channel. When installing the M.2 SSD for this product, please check the interface and protocol channel of the hard disk.
- Although the USB port of the product supports hot-swapping when installing M.2 SSD, it must be unplugged all power.
- When inserting the SSD, should be as gentle as possible to avoid scratching the components on the motherboard.
- When disassembling the hard disk case, please save all data properly to prevent loss.
- Since Windows 10 and above and Mac OS are the best compatible with NVMe, this product is recommended to get better transmission performance in Windows 10 or higher or Mac OS system.
|Downstream||M.2 NVMe SSD (Female)|
|Dimension||117.5 x 40 x 13.5mm|
1 x USB3.1 Gen2 Type-C to M.2 SSD (NVMe) Enclosure
1 x USB-C to USB-C Data Cable
1 x USB-C to USB-A Data Cable
1 x Heat Sink
1 x Silicone Pad
1 x User Manual
Shipping cost will be calculated during checkout. International duties & taxes may apply and are not calculated at checkout.
Tool-Free design allows quick and easy installation of your M.2 NVMe SSDs. Plug and play, no driver needed. The first time you use M.2 NVMe Solid State Drive, you need to format the disk. It will be safe for your memory data.
Adopts premium aluminum alloy shell, slim design, durable and excellent heat dissipation, reduced power consumption. Support UASP / Trim with ultra-fast transmission speed.
Twinkles: Record/Reading is going on
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Initialize a drive
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Create a partition in a drive
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
In the File System field, enter NTFS.
Set the Allocation unit size to Default.
In the Volume label field, enter <your name/reference>.
Select the Perform a quick format check box.
Clear the Enable file and folder compression check box.
Click Next > Finish.
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Initialize a drive
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Create a partition on a drive
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
The drive should now be accessible in Finder.
The drive may be damaged. Test with a known-working drive, or test the drive directly to a PC.
The operating system on the computer may not support reading and writing to the file system on the docked hard drive or SSD. Remember, Windows cannot read Mac or Linux file systems. Also, macOS can read but not write to NTFS drives.
If the drives came from a RAID (Redundant Array of Independent Disks), they would not be accessible in our docking stations.
If the drive uses 4Kn sectors, check the technical specifications of the docking station, and ensure it can read 4Kn drives.
You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.