USB 3.0-SATA III 듀얼 베이 HDD/SSD 도킹 스테이션(UASP 및 오프라인 복제 포함)
듀얼 베이 하드 드라이브 도킹 스테이션은 오프라인 복제를 지원하므로 컴퓨터 호스트 없이 쉽게 2개의 하드 드라이브를 복제하거나 복제할 수 있습니다!
하드 드라이브 복제 방법:
1. 2개의 하드 드라이브를 연결하고 원본 디스크와 대상 디스크를 식별합니다.
2. 전원 공급 장치를 연결한 다음 전원을 켭니다.
3. "복제" 버튼을 쉽게 누르면 오프라인 복제가 시작됩니다.
Support 2.5''/ 3.5'' SATA I/ SATA II / SATA III HDD SSD (up to 2 x 18TB)
Support USB 3.0 data transfer rates up to 5 Gbps, backward compatible with USB 2.0/1.1.
Support UASP (USB Attached SCSI Protocol) , provides faster transfers up to 70% faster read speeds and 40% faster write speeds over traditional USB 3.0.
Offline Clone: The docking station can operate offline cloning independent from a computer. Easy to duplicate data from one to another hard drive.
Automatic sleep mode after 30 minutes of inactivity saves energy.
Stable electricity supply, with a 12V 3A power adapter.
With LED indicator, lights on when power on.
Plug and play, no driver required.
Premium aluminium alloy casing for greater durability and better heat dissipation during full loading.
- Target Disk must contain more space than Source Disk.
- Any bad sectors on the drives in use may prevent HDD duplicator and cause overheating, which damages to the station.
- Do not try to insert or withdraw HDD or SSD when another hard drive running.
- Highly efficient 12V3A power supply makes sure a stable and reliable energy supply.
- The hard drive is recommended to format Mac OS Extended (Journaled) when using on Mac.
|Dimension||130mm x 115mm x 61mm|
|Downstream||2 x SATA III Interface|
|Power Input||12V 3A|
|Packaging Content||1 x USB to 2.5"/3.5" SATA6G Dual Bay HDD & SSD Docking Station with UASP
1 x USB Data Cable
1 x 12V/3A Power Adapter
Shipping cost will be calculated during checkout. International duties & taxes may apply and are not calculated at checkout.
The docking station can operate offline cloning independent from a computer. Easy to duplicate data from one to another hard drive.
Support SATA III at 5Gbps with UASP Quickly access 4K movie file in seconds no matter playing or editing
Supports all 2.5”/ 3.5” SATA I, SATA II, STAT III HDD SDD. To duplicate hard drives, it supports a maximum of 2x18TB hard drives.
The drive may be damaged. Test with a known-working drive, or test the drive directly to a PC.
The operating system on the computer may not support reading and writing to the file system on the docked hard drive or SSD. Remember, Windows cannot read Mac or Linux file systems. Also, macOS can read but not write to NTFS drives.
If the drives came from a RAID (Redundant Array of Independent Disks), they would not be accessible in our docking stations.
If the drive uses 4Kn sectors, check the technical specifications of the docking station, and ensure it can read 4Kn drives.
You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.
You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.
To confirm that Windows detects your USB device, complete the following:
Press the Windows key+R, type devmgmt.msc, and press Enter.
In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it. For example, a USB controller card would be under Universal Serial Bus controllers.
Your USB device is listed according to the name of the chipset.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Initialize a drive
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Create a partition in a drive
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
In the File System field, enter NTFS.
Set the Allocation unit size to Default.
In the Volume label field, enter <your name/reference>.
Select the Perform a quick format check box.
Clear the Enable file and folder compression check box.
Click Next > Finish.
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Initialize a drive
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Create a partition on a drive
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
The drive should now be accessible in Finder.